How to ensure the vulnerable parts of the wood crusher?

The wood crusher is a crushing type of mechanical equipment, so many of its internal parts are wearing parts. If you do not pay attention to it during use, it is very easy to cause wear or damage of these parts, so we must always Maintenance and maintenance of the wood crusher equipment to extend the service life of the vulnerable parts inside the wood crusher to ensure that it can be used for normal production operations. Of course, this can effectively guarantee the output and crushing efficiency of the wood crusher equipment. Even extending the overall service life, what do you need to maintain and maintain the wood crusher equipment?

First of all, we must first understand the vulnerable parts before carrying out the maintenance and maintenance work of the wood crusher. The blade is the one that is responsible for processing the waste wood in the crushing chamber, so we have to do it every time after the production operation. Check the use of the blade. If it is found to be worn, it should be sanded or replaced in time. When replacing it, make sure that it is the same as the other blade length, weight, material, etc. on the cutterhead, and ensure the overall cutterhead to a greater extent. The stability is secondly that the bearing is injected once every 300 hours, which not only reduces the wear of the bearing, but also ensures that the temperature of the bearing does not appear too high. If the lubricant is not injected, the bearing will be caused. The service life is greatly reduced, and the temperature is often too high or even deformed.

How to reduce the production cost of wood crusher?

Wood crusher equipment in the process of production operations, many inadvertent operations may increase production costs, and production costs will have an impact on the overall economic benefits of enterprises, in order to ensure corporate profits, our morning redwood crusher manufacturers through a variety of In summary, we have come to the conclusion of how to reduce the production cost of wood crusher. You can refer to the following points to reduce the production cost of wood crusher.

The first is that the wood crusher equipment will cause the motor or the diesel engine to reach the load at the moment of starting, and the power consumption and fuel consumption are very high when the wood crusher equipment is under load, so it starts at the wood crusher. The moment is that the production cost is very high, so we should reduce the number of starts per day of the wood crusher equipment, which can effectively reduce the production cost of the wood crusher equipment.

There is also the feeding speed because the speed of the feeding will affect the production cost of the wood crusher equipment. Once the feeding is too much, the wood crusher will be in an overload state for production. It also accelerates the wear of internal components, which leads to damage or wear of the components, which increases the production cost of the wood crusher equipment. The overload condition may cause the motor of the wood crusher equipment or the diesel engine to malfunction. There may even be a burnout situation, so we should maintain a uniform rate of feed when operating the wood crusher equipment.

New bamboo charcoal machine equipment

In recent years, bamboo charcoal produced in the market has become more and more popular. It is a new type of environmental protection mechanism charcoal, and bamboo charcoal has very high flammability and combustion resistance. It is a very good charcoal resource, so many users are investing in new types. Bamboo charcoal machine equipment uses bamboo to produce bamboo charcoal.

The new bamboo charcoal machine equipment must be used to produce high-quality charcoal. The equipment has been modified on the basis of the old-fashioned carbonization furnace, adding a lot of carbonization process, so that the carbonization furnace can be quickly carbonized, and the quality of the carbonized material is also very high. High, some manufacturers have no purification system installed in this equipment, can not separate the wood tar wood acetic acid, but the carbonized material is very oily, the smoke is too large in the carbonization process, not environmentally friendly. However, the new bamboo charcoal machine equipment created by Shuliy Machinery is equipped with dust removal and purification system, which can be environmentally friendly and carbonized. The carbonized material is not oily and is very crisp. It is very suitable for bamboo charcoal and can produce high-quality bamboo charcoal. of.

The charcoal produced by the new bamboo charcoal machine has high density, small volume and good flammability, which can replace fuelwood and coal. This product is especially suitable for heating and heating in the autumn and winter in the northern region, warming the greenhouse or making ordinary living fuel. The new bamboo charcoal machine series equipment includes a rod making machine, a carbonization furnace, a dryer, and other equipment.

The selection of bamboo charcoal is generally made by using older bamboo at high temperatures. The good adsorption capacity of bamboo charcoal has been recognized and loved by everyone. With the new bamboo charcoal machine equipment, the charcoal is sold well, and the market is very popular. At present, there is no uniform classification standard for bamboo charcoal in many areas. Generally, it is distinguished from the aspects of gloss, shape, and conductivity. The quality bamboo charcoal has the following characteristics:

1. High-quality bamboo charcoal has a high surface gloss with the naked eye.

2. High-quality bamboo charcoal is made of old bamboo that is more than 5 years old, so the structure is very tight, and it is not easy to break when tapped lightly.

3. The quality of the barrel carbon is 2-6cm in diameter, and the surface is basically free of cracks.

4. Because the conductivity of bamboo charcoal is closely related to the density, refining degree, water content and ash of bamboo charcoal, high-quality bamboo charcoal requires a small resistance value, which can be judged by using a conductivity meter. The smaller the resistance value, the better.

New wood chip dryer equipment

The new wood chip dryer equipment is a very common drying equipment on the market, which can dry wood chips, sawdust and other materials, so that these wastes are processed into other products after drying, which has the value they deserve, and also saves Eco-energy, promote the rapid development of energy-saving and environmental protection, what problems should be noticed when the new wood chip dryer equipment is drying materials?

1, low-temperature coking:

Reason: It often occurs at the time of ignition. The reason is that the individual bottom layers are not fluidized, and the local heat accumulation cannot be taken away to form coking. Sometimes, because the fine coal particles are blown together by the wind, they quickly burn to form coking.

Solution: Low-temperature cooking is loose and brittle, easy to remove. When the local fire is found, it should be promptly dredged with tweezers and cleaned to prevent future problems.

2, high-temperature coking:

Reason: Due to improper air volume and coal volume during operation, or due to insufficient boiling height, the coal particles are too large, resulting in a large concentration of coal at the bottom, more heat per unit volume, and the temperature exceeds the melting point of coal ash and coking.

Solution: The coke block with high-temperature cooking is solid and often needs to be shut down for treatment. Therefore, observation should be strengthened for prevention during operation. The yellow sand, or overflow slag, or cold slag after spraying water can be quickly added to the cooking area in the furnace, so that the temperature of the coal seam can be quickly lowered, and a small amount of water can be sprinkled on the surface layer, but the water is absolutely not allowed to immerse into the furnace wall. If measures are taken, the fire color cannot be changed, and the material layer is sticky, indicating that coking is inevitable. At this time, coal should be stopped, the wind should be stopped, and the soft coke block should be removed with steel brazing.

3, the raw materials do not dry at one time

Reason: The new wood chip dryer equipment is too small; the wind network wind pressure and flow calculation are incorrect; the rotary dryer is not used properly.

Solution: Increase the temperature of the new wood chip dryer equipment, but this method is easy to cause the fire inside the dryer. A good method is to replace or re-modify the drying equipment; the new wood chip dryer equipment manufacturer is required to recalculate the wind pressure and flow rate. Provide a design change plan according to the actual situation; negotiate with the new wood chip dryer equipment manufacturer to obtain the equipment manual and learn the correct use method.

3, the new wood chip dryer equipment inside the fire

Reason: The new wood chip dryer equipment is not used properly; the dryer equipment is too small to achieve the drying effect and the forced heating causes the fire; the design principle of the dryer equipment is problematic; the raw material does not suck and causes the fire in the dryer.

Shuliy wood crusher machine

The wood crusher is ideal mechanical equipment for the efficient production of wood powder. It can process wood, branches, miscellaneous wood, plates, and other raw materials into sawdust at one time, with low investment, low energy consumption, high productivity and economy. Good benefits, easy to use and maintain, etc., is the development of special equipment for the production of edible fungi or for the production of wood chips and high-density wood chips of sawdust.

The wood crusher machine can process wood, branches and other raw materials into sawdust at one time, and has the advantages of low investment, low energy consumption, high productivity, good economic benefit, convenient use, and maintenance. The wood crusher is particularly suitable for the processing of wood chips in the edible fungus culture medium. The wood chips after cutting by the chip cutting device have a small particle size and can be sent to the pulverizing device for further pulverization without drying.

Wood crusher scope

The wood crusher is suitable for the crushing of the following materials: especially suitable for crushing: miscellaneous wood, branches (dry and wet), corn cobs, scraps, building boards, bark, leaves and so on. (Note that the wood crusher is not suitable for the crushing of flammable and explosive materials)

Wood crusher structure and crushing principle

1. It consists of three parts: the body, the middle body, and the lower body.

2. The crushing knife has a 7-knife, a type knife, and a centrifugal knife.

3. The auxiliary machine consists of a fan, a dust collector and a dust collector.

4. The main crushing chamber adopts 7-knife, a type knife, and a centrifugal knife. It is coarsely pulverized, finely pulverized and centrifuged to re-pulverize. The motor drives the pulverizer rotor to run at high speed so that the high-speed airflow generated by the machine produces high strength to the pulverized material. Impact force, compression force, cutting force, friction force to achieve high-quality crushing function.

Large wood crusher machine

The large-scale wood crusher introduced the world’s high-end technology and adopted a double-motor-driven smashing mode, which completely changed the problem of dust in the wood pulverizer work. Our company has now put a lot of production into production.

The large wood crusher is mainly used for processing branches, wood chips, scraps, wood boards, raw bamboo, and other materials. At the same time, the equipment can also be used for cutting chips of fibrous stalk materials such as bamboo, thatch, corn stalk, and sorghum stalk. The sawdust produced by the large wood crusher is widely used in papermaking, edible fungi, mechanism charcoal, particle board, sawdust board, high-density board, MDF and other industrial production.

Working principle of large wood crusher:

The wood crusher machine is mainly composed of a pulverizing device, a spiral discharge, and a fan. The wood is sent to the pulverizing chamber of the pulverizer through the belt conveyor and can be sent to the pulverizing device for further pulverization without drying, and the pulverized finished product is sent to the collecting place by the screw. The large wood crusher is more complicated than the hammer-type wood shredder structure. The machine has reasonable design, low power consumption, and large output.

Performance characteristics of large wood crushers: Equipment performance has been greatly improved compared with other similar products.
1. The whole set of equipment is driven by a double motor. The machine has a stable operation, low energy consumption, high output, good quality of sawdust machine and low processing cost.

2. The wood shredder is a kind of hammer mill. It mainly uses the principle of blade chip and air current impact to pulverize the material to be crushed. The equipment is mainly composed of five parts: crushing, grading, conveying, unloading and dust removal. The traditional screening process is canceled, and the sawdust processed by the machine can be molded at one time.

Small peanut shell charcoal machine equipment

Small peanut shell charcoal machine equipment production charcoal material rich and low price: rural rice husk, peanut shell, fruit shell, cotton rod, soybean stick, sesame rod, corn stalk, corn cob core; furniture factory, wood factory, bamboo factory Sawdust, shavings, bamboo and wood corner scrap; plywood factory, dust and scrap of fine wood board factory; sugar cane bagasse of sugar mill; mountain grass, twigs, etc. can be used as material for producing charcoal.

Small peanut shell charcoal machine equipment has a lot of charcoal materials, such as thrown straw, wood chips, branches, and leaves, so that the bark bark is also completely capable of making charcoal. However, it cannot be produced directly, that is to say, only bark is not feasible. Due to the process of forming charcoal, wood fiber is needed, and the bark does not have wood fiber. The content of charcoal in the bark has arrived at the machine-made charcoal. The standard of charcoal, but no wood fiber, so the pointed will be very slack, and it is extremely difficult to form after carbonization. This is not the case when a factory with many bark materials is used. Short wood fiber is completely compensated. We just need to participate in the right amount of wood chips to form smoothly.

There are many materials for small peanut shell charcoal machine equipment, and some may not produce charcoal directly. Some other things need to be added to assist. From the overall situation, eucalyptus bark can be used for charcoal, so users who invest in small peanut shell charcoal machine equipment can boldly carry out this intention. The carbonization tank material (such as rod, log, bark, coconut shell) is heated and carbonized. The flue gas that occurs during the carbonization process is completely recovered, and then the combustion of the combustible gas is re-burned by spraying, cooling, purifying and the like. According to this method, the self-inflicted flammable gas is burned and self-contained, and the effect of energy-saving is reached. The smokeless gas is discharged in the whole process of production and reaches the national environmental protection needs.

Small straw charcoal machine promotes environmental protection economy

Shuliy Machinery is a professional charcoal machine manufacturer. In professional practice, small straw charcoal machine equipment is a charcoal machine production line composed of multiple equipments. The choice of the charcoal machine needs customers to choose according to their own needs. Generally, the production line of small straw charcoal machine equipment consists of four kinds of machinery: crusher, dryer, carbonization furnace and rod making machine. Customers can also increase or decrease according to the raw materials used. For example, when sawdust is used as raw material for production, it is not used by sawdust itself. The smashing can reduce the input of the pulverizer, so the user can go to the manufacturer to understand and purchase on the spot according to the needs of the company.

Small straw charcoal machine equipment will produce many different pores when the carbonization temperature changes during operation. Under the influence of these pores, the absorbability will increase with the change of temperature, and the running speed will also increase, which will make the efficiency become higher. Long-term work can also cause different degrees of damage to the shaft head. For these reasons, the Shuliy mechanical charcoal machine summarizes some methods for customer reference.

In the small straw charcoal machine equipment welding, the vulnerable parts are treated and corrected. After the initial grinding correction, the charcoal machine shaft head is inserted into the dried quicklime or grass ash, cooled to below 50 °C for complete grinding, and the grinding is not to the circumferential runout. More than 2mm, and the surface of the circumference has no obvious wetness and convexity. After the repair of the shaft head of the charcoal machine, it is strictly prohibited to knock or collide, so as to avoid damage to other parts of the surface area of the surfacing, and should be carefully stored.

Small straw charcoal machine equipment is the leader in the mechanism of charcoal production. Its emergence is to drive China’s new energy-saving fuel to the high end. The previous raw charcoal firing and use has been eliminated, and replaced by a new environmental protection mechanism charcoal. The charcoal usually made of small straw charcoal machine equipment not only has a high carbon removal rate, but also has a charcoal shape which is quite hollow and has a hexagonal shape, and the profit of charcoal is quite high. In the domestic and international sales market has been occupying the charcoal market, and will not waver in the short term, the future trend will go on, the advantage is leading, the first mechanism charcoal is a green and environmentally friendly fuel in sharp contrast with the previous original charcoal.

Secondly, in the quality mechanism, charcoal is pressed by high temperature pressure to make the compactness high, fuel resistance and heat generation, while the original charcoal is low in compactness after firing, so the durability is far worse than the mechanism charcoal. The small straw charcoal machine is a fully automatic production equipment with strong production capacity and high output, which can easily meet the market demand. This is very important for charcoal producers, so the utilization rate of the mechanism charcoal is also high.

Garri Processing Machinery

1: Introduction of garri processing machinery garri fryer machine:

Our frying pan is a stirred tank. Its heating method can be electric/gas.

2) This fryer is stirred with a “scraping” type. The heat transfer oil is its medium, so it is not sticky. Evenly mixed, no dead ends, make the material more fully mixed.

3) Two independent heating control systems, adjustable heating temperature, and automatic control.

4) There is no danger of open flames, explosions, and fires.

5) Easy to install and easy to operate.

6) The handwheel is shaken and discharged. It is efficient and practical.

2. Details:

Garri processing machinery garri fryer machine

Pot: T his product is a flat stainless steel pot, the overall roundness error is small, with a stirrer heightening to avoid paste pot phenomenon.

Heating System: Uses a variety of heat and other options available to customers in the form of gas, electricity and heating oil.

Electricity: Large heating area, temperature control, and even heat.

Gas: The gas is easy to use and the heating speed is fast, which meets some high-temperature requirements and is not limited by the factory voltage.

Electromagnetic: rapid heating, can consider the color, flavor, save 20% of similar products, environmental pollution.

Hybrid system: The mixing method uses a special tilting rotation to make the earth full contact between the agitator and the pot, realizing the auto transmission of the non-rotating and rotating integer ratio, so that the pot does not mix and die, more uniform material mixing, scraping the bottom more, thoroughly, It is not easy to paste the pot.

Garri processing line

Garri and cassava production is an impressive business opportunity in Africa, especially in Western and Central Africa. The production line mainly includes peelers, grater machines, hydraulic presses, screens and oil pans.
1. Moi cassava peeling part of the manufacturing machine:
Peeling involves removing the outer brown layer of the cassava tubers to reveal white/yellow meat. However, the peeler reduces waste, saves time and labor, and does more work in a short period of time; it can strip 2,500 kilograms of cassava in one hour, while manual stripping can only process 20 kilograms. The peeler is usually the most expensive machine in the entire range.
2. Cassava peeling machine
This machine grinds peeled and washed cassava tubers into a paste or mash, and can process up to 4 tons of raw cassava a day.
3. The hydraulic machine of the Gary machine:
This machine is equipped with a 30-ton hydraulic jack that can easily squeeze all the water made with cassava mud.
4.making machine screening machine:
This is the fiber/block with the ground, chopped and pressed cassava before frying.
5.Garri friers (garri processing machine):
There are basically two types of frying pans – mechanical and metal trays. Although mechanical fryers are much more expensive, they can handle more metal trays in less time than more time and labor. However, both can still complete frying work.
For those who manufacture machines on tight budgets.
A small-scale processing plant with a full range of machines can produce up to 1 ton of gari (about 20 50 kg bags) within a day. If you have a tight budget you can remove mechanical fryers and peelers from the list because they are The two most expensive options. However, you will need more labor and may produce fewer garis in a single day.
company information
Manufacturing machine manufacturer
Shuliy Machinery is engaged in cassava processing machinery, tapioca starch processing machinery, tapioca production machinery, tapioca starch production line, sweet potato/potato starch processing plant, tapioca production line, manufacturing machine, gluten washing machine, syrup production line, glucose syrup processing machine, high fruit powder corn syrup With the processing machine, we can provide a complete set of production lines and turnkey projects.